FARO Laser Tracker Rental vs. Buying: A Metrology Buyer's Honest Scorecard
2026-11-10 by Hanae Okamoto
-
Why I'm writing this (and what it isn't)
-
1. FARO laser tracker rental vs. purchase (and why my first answer was wrong)
-
2. FARO Arm CMM vs. fixed CMM: portability isn't free
-
3. Where I overbought: digital micrometers and a compact thermal camera
-
4. "What is the best Fluke multimeter for electricians?" — my honest answer
-
What my current checklist looks like
Why I'm writing this (and what it isn't)
I've been handling capital equipment and inspection-tool purchases for eight years now. In that time I've made seven mistakes I would classify as genuinely expensive, totaling roughly $84,000 in wasted budget. Most of them happened for the same dumb reason: I compared products on the spec sheet instead of comparing them on how our team would actually use them.
This isn't a review, and it isn't a buying guide that tells you one option wins everywhere. What I can do is lay out four comparisons the way I wish someone had drawn them for me back in 2017, when I still trusted the brochure version of reality. The four dimensions: FARO laser tracker rental vs. purchase, FARO Arm CMM vs. fixed CMM, hand tools (specifically digital micrometers and compact thermal cameras), and Fluke multimeters for electricians.
One more thing before I start. I keep a pre-purchase checklist now. We've caught 47 potential errors with it in the past 18 months. Most of those errors were the same category: buying capability we didn't need.
1. FARO laser tracker rental vs. purchase (and why my first answer was wrong)
In September 2022, I rented a FARO Vantage for what I thought was a one-week job. The quote was $3,200. The job ran three days long, and I had to extend the rental for another $2,400. That was the moment I started taking this comparison seriously.
Here's the cost structure as I've experienced it:
- Rental: $2,500–$4,000 per week depending on the model and the working volume
- Purchase: $80,000–$150,000 for the tracker itself, plus $8,000–$12,000 per year in calibration, software seats, and service contracts
The conventional wisdom is that you rent for occasional use and buy once you're using it more than a few times a year. My experience suggests that threshold is way too low. Owning a laser tracker isn't just capex — it's calibration cycles, software maintenance, and the training hours that nobody puts on the requisition form. If you're using it fewer than 35 or 40 weeks a year, I'd argue rental plus a service contract on your reference spheres is probably cheaper, though I should note my numbers are pulled from our own usage logs, not a formal study.
One thing I'd flag on the rental side: make sure the calibration certificate is current and traceable. ASME B89.4.19 covers performance evaluation for laser trackers, and NIST traceability is the thing your auditor will ask about. We got burned once — or rather, our quality manager got blindsided — by a rental unit whose cert had expired six weeks before it arrived. Nothing like explaining that in a customer audit.
But here's the counterintuitive part that took me a while to accept: renting also gives you model flexibility. If you're mostly tracking large assemblies, rent the unit with the bigger working volume that month. If it's a small fixture job, rent smaller. You can't do that when you own one machine.
2. FARO Arm CMM vs. fixed CMM: portability isn't free
I want to be careful here, because the conversation around portable vs. fixed measurement has gotten weirdly tribal. The way I see it: they're different tools for different jobs, and neither has made the other obsolete.
My experience with a 12-year-old fixed CMM and a 6-year-old FARO ScanArm suggests the boring answer is the right one. In a temperature-controlled room with high part volumes, the fixed machine still wins on repeatability and throughput. Where the FARO Arm CMM earns its keep is on-machine inspection, field work, and setups where the part can't come to the metrology lab.
ISO 10360 is the standard that governs acceptance and reverification testing for CMMs. When we bought the arm, I leaned hard on that standard to compare the arm's volumetric performance against the fixed machine's. The numbers were closer than I expected for the specific tolerance bands we work in.
I don't have hard data on throughput comparison — I wish I had tracked cycle times more carefully from the start. What I can say anecdotally is that the arm's real advantage isn't speed, it's the setups you don't have to do twice.
3. Where I overbought: digital micrometers and a compact thermal camera
Two purchases I'd make differently today.
Digital micrometers. I bought six at once, assuming every inspection station needed one. In practice, four of them get used fewer than five times a year. The micrometer isn't the problem — the problem was that our tolerance band didn't require 0.001 mm resolution most days. Calipers covered about 70% of what we actually measured. If I were buying again, I'd buy two good micrometers and put the rest of the budget into calibration management.
The thermal camera. I picked up one of those compact One Gen 3 thermal cameras for the maintenance team, thinking we'd use it weekly for predictive inspection. We used it maybe a dozen times in 18 months. It's a solid little tool — I'm not knocking the hardware — but the ROI I wrote on the requisition form was fiction. The lesson, which took me a while to absorb, is that tool utilization follows workflow, not enthusiasm.
It took me about three years—or rather, closer to four when you count the revision cycle—to understand that the real cost of buying tools isn't the purchase price. It's the calibration calendar, the training time, and the shelf space. Every micrometer and camera you buy adds to that overhead. If I remember correctly, our calibration vendor's minimum charge alone went up by about $1,100 a year after that batch of purchases.
4. "What is the best Fluke multimeter for electricians?" — my honest answer
This question gets a ton of search traffic, and most of the answers obsess over model numbers. My take: start with the CAT safety rating and the actual duty cycle, not the feature count.
If your electricians are working on distribution panels, the CAT rating should drive the choice. IEC 61010-1 defines the CAT levels, and a CAT III 600V meter is the floor for most industrial work — a CAT IV rating matters if they're going near service entrances. The 117 is a fine everyday meter for a lot of shops. The 87V is a serious upgrade if you need true-RMS and tighter accuracy. The 1587 adds insulation testing, which is lovely on paper.
My mistake: I bought the 1587 for our team because it had insulation testing and logging. Two of our electricians used the insulation tester exactly once in 14 months. We paid for capability we didn't use, and the meter's a bit bulkier in the hand as a result. If I were buying for our actual workflow today, I'd buy the 117s and rent a 1587 when a specific job calls for insulation testing. That said, if your crew genuinely does motor maintenance weekly, the 1587 is the right call — the math changes completely.
What my current checklist looks like
If you're staring at the same decisions, here's the short version of what I'd tell my 2017 self:
- Laser tracker: rent unless you're using it 35+ weeks a year. Verify calibration certificates on every rental. The model flexibility is worth more than people realize.
- CMM: fixed CMMs still win in controlled environments with high volume. FARO Arm CMMs win on-field and on-machine work. Don't treat it as a religious war.
- Hand tools: buy for the 70% case, rent or borrow for the 30%. The calibration overhead is the number that actually matters.
- Fluke multimeter: CAT rating first, duty cycle second, features third. Most electricians don't need the top of the line, and the ones who do already know it.
Bottom line: the expensive mistakes in metrology rarely come from buying the wrong brand. They come from buying for the job you imagine instead of the job you actually run. I learned that the hard way, roughly $84,000 worth of hard way, and I'd rather you didn't have to.
Leave a Reply